home » Etiquette » Decor crocodile skin. Decorative plaster with the effect of the skin of different animals

Decor crocodile skin. Decorative plaster with the effect of the skin of different animals

Before applying the design effect, it is necessary to carefully prepare the surface. Surface Type #2, Method 1.
Application conditions:
air temperature: from 5°C to 35°C
relative air humidity - no more than 75% (recommended - 60%).

Applying the base effect

1 Apply the first coat according to the MM6 Design Effect technique. Products for it are listed in the Base layer section in the detailed estimate. Let the surface dry for at least 36 hours. After that, you can start gluing the stencil.

Applying glue to the stencil

2 The stencil should be fixed on a vertical plane with the white side up and surrounded by plastic wrap. A thin layer of Colle Aérosol Repositionnable adhesive is sprayed onto the surface of the stencil from a distance of twenty centimeters. If necessary, the nozzle can be switched to the position for spraying a wide torch.

Sticking the stencil on the wall

3 Mark the area where the stencil is located using a level, tape measure and masking tape. Wait five minutes after applying the adhesive layer, paste the stencil and strengthen it using a pressure roller.

4 Remove the green mounting film and select the stencil elements, referring to the diagram.

5 The stencil is rolled again with a pressure roller, with pressure on it.

Filling the stencil

6 Fill the stencil with LoftBeton putty. The stencil should be filled in two stages - first half the depth. After 12 hours, after the first layer has dried, fill completely and level the surface with a spatula to the level of the stencil to obtain a smooth surface.

Applying the final effect

7 After the Loft-Beton is completely dry (12 hours), sand the surface with fine sandpaper. Apply a coat of Suprime-100 primer, allowing it to dry for 8 hours.

Applying the base effect

Applying glue to the stencil

Sticking the stencil on the wall

4 Remove the green mounting film and select the stencil elements, referring to the diagram.

5 The stencil is rolled again with a pressure roller, with pressure on it.

Filling the stencil

Applying the final effect

7 After the Loft-Beton is completely dry (12 hours), sand the surface with fine sandpaper. Apply a coat of Suprime-100 primer, allowing it to dry for 8 hours.

Very often in a stylish interior, designers use natural material under the skin of a crocodile. Beautiful leather furniture in the photo, decoration is an object of elegance and status. Most often, this refinement is awarded to furniture decoration. Wall panels made from natural raw materials will cost a fabulous budget, and why exterminate crocodiles for this purpose, if decorative plaster today is able to fulfill any dream.

New building mixes and various accessories will quickly and easily imitate any animal skin on the wall in the room. natural fabrics and fur are gradually becoming a thing of the past, because designers create artificial masterpieces no worse than their natural counterparts.

Even furniture finishes look great with a leather substitute, and decorating a wall under the skin today will not be a particular problem, over time, many different technologies have appeared that you can use on your own. Moreover, you can do the finishing with your own hands by studying additionally any video on this topic.

The technology of applying decorative leather to the wall

A strengthening primer with a quartz addition is applied to the prepared surface, it will be easier to purchase a ready-made mixture for plastering under the skin.
When the primer has dried, it is necessary to apply a coating with a layer of one and a half to two millimeters. This base layer will serve as the basis for shaping the structure using special tools. An impression can be made with a special figured roller under the skin or with a conventional construction stencil. On the stencil, each side repeats each other, and you can order a stencil at a hardware store.
In places where a joint has formed, we make an additional print with a special rubber stamp. With the same flexible stamp, you need to create a texture on the radius surfaces.
After the entire surface dries evenly, it will be necessary to process it with sandpaper, capturing all the decorative finishes. So, you can remove all the influxes and flaws. Then experts recommend getting rid of the dusting of the surface with a brush. The plaster mixture can be taken ready-made, tinted with color, or you can paint the finished surface. If the mixture is already colored, then you need to apply only a diluted varnish or a special coating, so that no smudges remain.
When painting, you need to disperse smudges so that they are not in the pores, and you need to get rid of spots with more saturated light. At the end of the finish, you need to apply a decorative layer with mother-of-pearl with a roller. If you want to enhance the effect genuine leather, then apply an additional tinted composition to the surface with a shade of marsh color, approximately the same as a real crocodile. To avoid gaps, and get a uniformly painted surface, you need to use a special sponge.
After applying the top layer, we expose the texture and show the bottom layer in places. On the recommendation of the masters, we additionally decorate the surface with a glossy varnish, so we can achieve a wet effect.

Plaster under the skin of a crocodile in the interior

Decorative coating under the skin looks very catchy, pretentious. Naturally, any interior with such a design turns out to be stylish and luxurious, any room with such walls will be a bold step, and original design leave a lasting impression. The leather-like design is suitable for an interior conceived for the style of a safari or for modern styles art deco and art nouveau.

Today, chic and luxury are returning to interior design and, of course, the use decorative finishes is not limited to its use only in furniture. An interesting option looks tiles made under the skin, wallpaper, panels. But the most successful performance is considered to be decorative plaster under the skin of a crocodile, because the designer always has the opportunity to change the texture, relief, and color schemes, perhaps, to come up with shades from orange to black. A good design solution would be to use such a finish for the office, hallway and kitchen.

If you plan to decorate your walls with crocodile skin decoration, then the main thing is not to overdo it in the interior with such a finish. It is better to limit yourself to some accessories, for example, door handles, rugs, pillows, than to turn your room into a leather world with leather-like floors and walls, because even a small element of a leather pattern on the wall will help make the atmosphere in the room warm and cozy.

Decorative plaster under the skin is becoming increasingly popular in interior design. A well-made coating looks expensive and is not cheap. In order to save money on the services of a master, you can learn how to make imitation leather with your own hands.

First of all, you need to level the walls. Minor defects will not interfere, since the finish coating under the skin of a crocodile, snake, stingray or elephant involves applying relief pattern. It is enough to make the surfaces smooth and vertical.

Gypsum-based finishing putties are used to level the walls. After drying, all surfaces must be treated with primer intended for textured plaster. You need to prime in 2 layers, drying each for several hours. The time required for drying, the manufacturer indicates on the packaging of the mixture.

To apply decorative plaster with a leather effect, you will need the following:

textured mixture "Jungle", "Africa" or other brands;
a special roller with a pattern for crocodile or snake skin;
spatula or trowel;
plastic grater;
paint and roller;
wax or varnish.

In addition to a roller to create a texture that repeats the skin of reptiles, you can buy a stencil or stamp with such a pattern. You will have to do it yourself to imitate the skin of an elephant or crushed bull skin.

How to make textured plaster under the skin

Moisten the prepared surface with water. Ready mixtures may seem too thick, but they can be diluted with water, unless otherwise specified by the manufacturer. Textured plaster should be applied in a layer 2-5 mm thick, trying to distribute it evenly.

The basis for imitation of the skin is applied to the walls with a wide spatula or trowel. Strokes should be wide and long, they should be performed with the same effort when pressing on the tool. Only in this case the layer will be of the same thickness. Dry the applied layer for 1-2 minutes so that it grabs a little.

To make a texture resembling a crocodile shell, proceed as follows:

Moisten the surface of the roller with water. This is necessary so that it does not stick to a thin layer of plaster.
Starting from the top edge of the wall, slowly roll the roller over the surface. Movement must be continuous and in only one direction.
Roll the next strip with an overlap of 1-2 cm to the area with the finished pattern. If necessary, correct the pattern manually, adding scales at the junction with a stick.
Carefully go through the outer corners with a roller or stamp.

The alligator pattern can also be made using a stencil. A film with a ready-made scale pattern is sold in construction companies. It must be fixed on a wall moistened with water, and then apply a plaster mortar with a spatula, pressing it with force into the slots of the stencil. Dry the surface a little and carefully remove the film. Convex scales will remain on the wall. The stencil is reusable, so you need to attach it next to the finished area, combining parts of the picture. Repeat process.

How to imitate the skin of a bull or an elephant

For such imitations, even the usual finishing putty on gypsum is suitable. But it is better to use mixtures to create textured surfaces. They have a fine-grained structure, which allows you to get a higher quality coating.

Plaster with the effect of the skin of large mammals is different from imitations of reptile scales. It has no pronounced pattern elements, and dressed cattle skin is usually quite smooth. Using it to finish furniture, manufacturers resort to crushing and the formation of small beautiful folds.

When decorating a wall under wrinkled skin, you can use thin and durable paper such as parchment or drawing tracing paper:

Apply a thick layer (5 mm) of plaster on the wall and leave to dry.
Dampen a large sheet of paper with water. Crumple it, forming arbitrary folds.
Press the crumpled tracing paper against the wall. Roll with a rubber roller so that wrinkles and uneven paper are imprinted on the plaster.
Carefully separate it from the wall, trying not to smear the pattern.
Repeat the process on the adjacent area.

To prevent the wall from looking made up of identical pieces, you can prepare several sheets of tracing paper and use them in turn. In this case, you need to combine the folds, as if continuing the pattern. The seams at the joints can be smoothed with a brush.

It is also easy to make an imitation of an elephant skin. For work, you need to prepare a large piece of gauze. Apply a thin layer of textured plaster to the wall.

Moisten gauze and stick to a fresh, dry surface. The fabric should not be leveled, natural folds will add even more credibility and imitation volume. Apply another layer of solution on top, and then remove the gauze without waiting for the layer to dry. The grainy pattern with folds successfully imitates rough skin animal.

leather wall paint

Decorative plaster "crocodile skin" or other imitation will be even more believable if it is painted appropriately. This will require acrylic paint at least 2 shades. First you need to apply a light layer. Coloring is done with an ordinary short-haired roller.

After the wall dries, you need to prepare a dry rag and dilute the paint of a darker shade. Apply it with a roller on the wall, painting over all the depressions of the relief. With a dry cloth, wipe the damp surface with force, removing some of the fresh paint from the convex places.

Crocodile skin can be additionally decorated by applying greenish areas to the edges of the scales with a foam rubber sponge. After that, dry the wall for 24 hours and cover it with a thin layer of wax. Polish to a shine. If desired, the wax can be replaced with a clear varnish.

When decorating walls for expensive types of leather, you need to remember that you will also have to buy the appropriate furnishings for such a room. This design is well suited for design in the Art Deco style, ethnic or colonial interior.

Extravagant, unique, exotic and spectacular. It is such a decorative plaster with a leather effect. It is suitable for all those who want to make the interior refined and elegant, while not being afraid to experiment with atypical solutions. People are much more likely to choose simpler solutions like bark beetle or more classic options like Venetian. The creation of "leather walls" is considered a very bold decision, because it radically transforms the interior.

Scope of application and invoice options

The use of leather texture for many will be a very controversial decision. The fact is that if the walls are finished with "leather", then it can be problematic to choose furniture for them. And matching furniture in the same style is not cheap. Decorative plaster under the skin is used only in the interior, and in most cases in non-residential premises. Often this finishing option is used in cafes, hotels, restaurants, etc. However, this does not prevent you from using such a solution for the interior of your own apartment.

Finishing under the skin, of course, is an extraordinary solution used in unusual places. It could be a Chinese restaurant or an apartment in oriental style. It should also be understood that not all skin is the same and it is possible to imitate the skin of various animals. The most popular are the following invoice options:

Crocodile skin
giraffe skin
elephant skin
Snake skin
Stingray skin

Working tools for creating skin textures

Decorative plaster with a skin effect is created largely thanks not so much to the textured mortar as to special tools and working techniques. Of course, there are special plasters to create a skin effect, but they only simplify the work, because the whole secret is in the tools. As for the solution itself, you should choose a thin-layer textured plaster with good adhesive properties and a high level of plasticity.

In addition to the standard set of tools (trowel, trowel, trowel, etc.), we will need special tools. The rubber stamp is one such tool. It is used 15 minutes after applying the plaster. They should press the still raw, but already slightly dried, material. However, such stamping can seem tedious, so there are more simple options skin imitations.

A special relief roller with a pattern is another essential tool for creating the desired texture. It is usually used when decorative plaster is applied under the skin of a crocodile. The drawing on the roller is looped, so a “continuous skin” is transferred to the wall. This method will be discussed in more detail a little later.

A very difficult way to create skin texture is to use a stencil. Such stencils are applied to the wall even before plaster is applied to it. After a while, they are removed, creating leather patterns. After drying, the plaster is processed with a plastic float, smoothing out all surface irregularities. With this method, we get a slightly voluminous drawing.

To create the effect of the skin of a giraffe, there are also special tools. But this technique is very complicated, because it requires drawing each element of the texture, which takes too much time. Also, such work requires special skills, so a beginner is simply not able to do it on his own.

Crumpled paper, although not a special tool, is still worthy of mention. It is also pressed against a wall covered with mortar, as is done with stamps. When she climbs, an embossing appears on the wall, creating the effect of shriveled skin.

Crocodile skin - do it yourself

Decorative plaster crocodile skin is created using a special roller. But first you need to preparatory work. They are quite typical. First, the wall is cleaned of old coatings, and then leveled. Ideally smooth surface as for painting is not required. However, bumps and depressions should also not be. After that, a primer coating with quartz filler is applied. This will help the layer of decorative material to be stronger and not fall off after application.

Decorative plaster with the effect of crocodile skin is done after the primer has dried. It is enough to apply a coating with a thickness of not more than 2 mm (thickness up to 5 mm is allowed). As previously written, you need to use a thin-layer textured plaster. It can be tinted in advance, but then the decorative effect of the skin will not be so expressive. It is best to paint the coating at the end, then it will be possible to create overflows of color, which will give the surface a more natural look.

Decorative plaster is applied with a trowel and leveled with a spatula. Again, a perfectly smooth surface is not required, because we will change the texture. We give the applied coating to dry a little, and then we already work with a roller. We make the wiring with a roller from top to bottom or from bottom to top. The scales on its surface will move to the wall. However, in this case, joints are formed that do not look very nice, although not very noticeable. They are removed using a rubber stamp with larger cells. They are passed through the joints, which will help correct the uniformity formed by the roller.

After the stamp, sagging and flaws also remain, as from joints. It is best to remove them with a brush, drawing some scales by hand. To enhance the effect, the dried surface can be coated with glossy varnish, mother-of-pearl paint, or a special compound based on colorless wax. However, before finishing, the wall should be sanded to remove any remaining flaws and sagging from decorative plaster.

The final layer will create an additional color or shade (the second option is more desirable). It is applied with an ordinary roller, taking away excess material from the surface with a cloth. Decorative plaster with the effect of crocodile skin after the last layer, whether varnish or paint, will look natural.

Master class on creating the effect of reptile skin

Other textures of decorative plaster under the skin

As mentioned above, decorative plaster helps to imitate the skin of various animals. Most often, people are interested in crocodile skin, but it is worth dwelling on other options.

The skin of a bull is created using ordinary thin tracing paper and a roller. All you need to do is wrinkle the tracing paper well, and then smooth it and attach it to the damp wall. After that, the tracing paper is rolled with a roller, transferring its shape to the wall. All the bends made on the tracing paper will be transferred to the wall, and after the correct coloring, the surface will become similar to the skin of a bull.

Elephant skin is made even easier. Moreover, almost any textured plaster is suitable for such a texture. For work, we need ordinary gauze. It is applied to the decorative solution on the wall with the entire surface. The gauze can be pre-folded in several layers. Then another layer of solution is applied to the gauze, with which it is pressed and fixed in one place. Let the solution dry a little, and then tear off the gauze. The resulting pattern will resemble dry elephant skin.

This is the easiest way to create a skin effect. The simplest and cheapest textured plaster should be used, as it will have a high consumption due to the application method. It is advisable to choose a mixture that can be applied with a roller. So it will be more convenient. You can apply a second layer with a spatula, but it's a little more difficult.

Painting for realism

Decorative plaster with a leather effect necessarily requires painting. Although the solution can be tinted in advance, it is still better to use a white material, which will be dyed at the end. Exactly correct painting plays a decisive role in the creation of the selected texture. And the point here is not only in the right color, but also in creating shine with the right tone of the picture. If you just paint everything with a roller in one color, then even the most professional work done before painting will end up looking terrible.

Standard painting is carried out in several layers. At the first stage, varnish or acrylic paint is applied. Immediately after that, the coating is carried out with a foam float so that the color is not uniform everywhere. To do this, it is enough to make the wiring in wave-like movements.

After drying, another layer of varnish or paint is applied to the wall. This layer should be darker than the previous one. Again we pass over the surface with a foam rubber grater. This is done in order to collect excess paint on the wall. At the last stage, a translucent or glossy varnish is applied. The last option is necessary when creating the reptile skin texture. If we are talking about elephant skin, then it is enough for her to walk with a roller, only once with the usual paint of the desired color.

Subtleties and tips

When everything has been said, I would like to focus on some points that can greatly simplify your work.

Working with a roller with a reptile skin pattern, it must be constantly moistened and washed. If you work with a dry roller, then it can tear off the still damp plaster. You need to wash it in order to clean it from the solution adhering to it. Otherwise, the solution will ruin the entire drawing.
If you need to apply decorative plaster under the skin on a column or at the corners, then you should buy two textured rollers. You will work with one, and cut off the work surface from the second. It will be flexible, and it will be possible to process corners and radius surfaces with it. Not very convenient, but very practical.
How intensively should the created texture be sanded before painting? It is believed that it is necessary to process the surface with sandpaper so that no more than half of the relief is removed.

Applying the base effect

Applying glue to the stencil

Sticking the stencil on the wall

Filling the stencil

Applying the final effect

Applying the base effect

Applying glue to the stencil

Sticking the stencil on the wall

Filling the stencil

Applying the final effect

The technology of applying decorative leather to the wall

Plaster under the skin of a crocodile in the interior

How to make textured plaster under the skin

How to imitate the skin of a bull or an elephant

leather wall paint

Scope of application and invoice options

Working tools for creating skin textures

Crocodile skin - do it yourself

Master class on creating the effect of reptile skin

Other textures of decorative plaster under the skin

Painting for realism

Subtleties and tips

Similar articles