home » Children » How to stretch the top of your boot at home. Special means for stretching shoes

How to stretch the top of your boot at home. Special means for stretching shoes

AND Sometimes in the process of choosing boots, it is not possible to find an instance with a suitable volume of the bootleg. That is, they are available either a little wider, or vice versa - narrower. Many tops, if you look closely, have a sewn-in elastic band (Fig.).

If one is present, all that is needed is to cut the lining from the inside of the shaft (one cut in the center, it is possible for the entire length), which prevents this elastic band from stretching. If elastic is not provided, then the volume of the bootleg can be increased by stretching in a shoe shop.

From the point of view of time and money, master shoemakers recommend choosing those bootlegs that are slightly Narrower. Why? Because on special rules it is much easier (respectively cheaper) than suturing. When stretching the risk to change appearance boots for the worse (as opposed to suturing associated with tearing the lining and changing the location of the back seam) - minimal.

Note. If stretching is planned, then cutting the lining (releasing the elastic, if any) is highly undesirable. The skin of the shaft will stretch only after the stretch limit of the elastic has been reached. It is better to release the gum after the stretching procedure has been completed (if there remains a need for this).

For a girl, boots perform not only a protective, but also a decorative function. They will protect the legs from cold, snow and rain, complement and emphasize any outfit ensemble. Every fashionista can face the situation when the boots are a little small in the bootleg. In this situation, you can solve the problem yourself.

In what cases is it necessary to cut the elastic band

Modern manufacturers, when sewing boots, use the same volume parameters of the shaft. When choosing, you may encounter a problem when the boot is small in the shin area, and the zipper does not close completely. There is a different situation: the clasp turns out to be completely fastened, but in this case, the boots strongly squeeze the area of the bootleg. This can lead to serious health complications, and this type of legs will not be particularly attractive.

Therefore, the choice of shoes should be approached very carefully. You can contact specialized ateliers, where professionals will sew shoes according to individual parameters. However, this method will be significantly different from buying shoes in a regular store with a pricing policy.

In the case of a small volume of the shin of boots, the problem can be solved in several ways: stretch the area of the bootleg on the boots yourself using home methods or cut the elastic band. The first option is not the most practical, since leatherette products can be damaged after such procedures. Therefore, cutting the elastic bands in the bootleg area will be the most effective and efficient way.

Important! Please note that this solution will only help in the situation if the lock does not fasten just a few centimeters or the slider fastens completely, but the product squeezes the leg. If the lock stops even in the middle of the zipper, you should refuse to buy and look for a better option.

Tips for cutting gum on boots

A few additional tips will help you competently, accurately and correctly conduct the process:

The cutting process should be carried out from the wrong side. In most cases, this is enough to ensure that the bootleg area becomes the required volume;
Experts recommend cutting the material in the middle without affecting the seam area. When cut on the sides, the seams may begin to stick out. This will cause discomfort when using a pair. There may also be damage to the pantyhose or hooks on the trousers;
At the beginning of work, take special interest in the location of the rubber bands. Many manufacturers place it under the main lining, which will complicate the process. In this case, it is better to turn to professionals in a shoe atelier;
If the boots are designed for use in the autumn-spring season, on most models the lining is sewn on from a fabric material (for example, fleece). After the end of the process, the material can be hemmed.

Reference! When buying shoes, pay special attention to the quality of the gum located in the boots. It should be of high density and elasticity. Otherwise, poor quality material will quickly spread, which will lead to unforeseen cash costs: repairing an old pair or buying new shoes.

How to properly cut the gum on your boots

First of all, it is necessary to prepare all materials and tools for a comfortable process.

Preparation:

boots;
nail scissors;
blade (in case you have to rip open the inner lining);
needle;
threads to match the product.

Attention! The technological process is recommended to be carried out in the afternoon (the best choice is in the evening). The muscles of the legs by this time had already stretched enough and swelled.

The course of work does not have a high level of complexity. With the help of a blade, the lining is carefully torn in the area where the ribbon is located. The cutting process is best done with nail scissors. Using a tool, cut the gum in the center.

It is recommended to cut the ribbon a little short of the position of the bottom line. At the end, you must put on boots with the usual products: tights, leggings or trousers (in the case when they are tucked into shoes). The lock itself should be fastened and a little like shoes around the house. This is necessary in order to understand how the product sits on the leg after the procedure.

If one incision was not enough, you can make several more, located next to the central one. The main thing is not to cut the elastic close to the seam so that the protruding threads do not interfere with the use of products. At the end of the work, the lining fabric is sewn up with small stitches. Boots are ready. After such actions, the elastic band will be weakened and help the shoe to accurately transform when using it.

In the process of work, carefully make sure that only the elastic is cut, and not the material of the products itself - leather or suede. With possible damage, boots are difficult to sew on their own. In some situations, specialists cannot cope with such a problem, so you have to go to buy new ones.

Stylish and comfortable shoes are one of the main accessories for every girl. Fashionable boots will warm your feet in cold weather and help emphasize the individuality of their owner. In some situations, the boots are small in the calf area, the clasp does not fasten just a couple of centimeters. A few simple recommendations will help any girl solve this problem.

Many women, when buying boots, are faced with the problem of a discrepancy between the width of the bootleg and the volume of the leg. Most models are sewn according to standard measurements, and therefore the products are not suitable for all customers. This does not mean that you should refuse the pair you like or buy shoes a few sizes larger. There are many options for how to stretch the bootleg at home.

Freezing boots

The freezing method allows you to effectively expand leather shoes. This is one of the easiest ways to stretch your bootleg at home.

Shoes must first be prepared for the procedure. To do this, take a large bag with a plastic zipper and fill it halfway with water. Squeeze out all the air from the bag, leaving a small gap in the corner. Bring both plastic sides together to close the bag.

The volume of the bag should be chosen based on the size of the shoe and the part to be stretched. If it is necessary to expand only the heel or toe, a liter bag is enough for the procedure. To stretch the ankle high boots a 3-4 liter bag will do.

Place the filled bag in the boot in the place that needs to be enlarged. For example, to stretch the top, you can fill the entire lower part with unnecessary paper, and put the prepared inventory on it. It is necessary to evenly distribute water over the entire stretch area and place the boots in the freezer.

When the water is completely frozen, remove the shoes from the chamber and leave the ice to thaw.

Warm up stretching shoes

There is an equally effective way to stretch your boots at home. Before the procedure, it is necessary to put on 3 pairs of thin socks and shoes. If it is difficult to get your legs through, you can remove one pair of socks.

When the shoes are on your feet, you need to heat up the part that is tight with a hairdryer. The warm-up time of the leather boot should be at least 30 seconds. It is recommended to select the maximum power on the hair dryer. Warmed skin needs to be kneaded, fixing the legs in a comfortable position. Do not take off your shoes until the leather is completely cool, otherwise it will return to its original shape. Then remove all excess socks and try on boots.

This method can be used to stretch all parts of the shoe. It is also suitable for widening the shaft of high boots.

Shoe expansion with special devices

For those who are interested in how to stretch the bootleg at home with minimal harm to shoes, there is a special device. For soles and tops apply different types stretch marks. Such devices are a wedge with a turning handle. The device is inserted into the boot and opened for a few minutes so that the skin is stretched to the desired width.

Stretching devices are commonly used in shoe shops. But they can also be used at home. Special skills and knowledge are not required to use the wedge. The main thing is to properly fix the boot.

A professional wedge can stretch shoes made of leather, suede and even rubber.

Stretching chemicals

To expand individual parts leather shoes special products are produced in the form of sprays. Before use, read the instructions from the manufacturer. It describes in detail how to stretch the tops of the boots. The manufacturer also indicates a list of materials that can be processed with a particular agent. Most of these sprays cannot be used on suede shoes.

It is also important to pay attention to the composition of the sprays. Some manufacturers add alcohol to the product.

Before use, it is recommended to apply a small amount of spray on the inside of the lower leg or other inconspicuous place and observe the reaction. If the skin has not changed color and appearance, the product is suitable for use.

The distance of applying the stretching spray is up to 15 cm. Immediately after spraying the product, you need to put on boots and walk in them for a while.

Stretching the skin with alcohol

70% alcohol is often used to expand leather shoes. In this concentration, alcohol does not harm even suede products.

How can you stretch the top of your boots at home with alcohol? It is necessary to spray with a spray bottle on the area of \u200b\u200bthe shoe that needs to be stretched. Alcohol should be applied evenly over the entire treated area. Then put the shoes on your feet and wait 30 seconds. During this time, the alcohol will be absorbed into the skin.

In order for the shoes to stretch properly, it is recommended to remain in them for some time after the alcohol has dried. Many believe that this is the cheapest and easiest method of how to quickly stretch the top of your boots at home. In most cases reach desired result succeeds the first time.

Application of castor oil

This remedy is often used to soften rough skin. Therefore, many masters, when asked how to stretch the bootleg at home, advise this tool. Castor oil perfectly stretches the skin with minimal damage to the product.

To increase the shaft, you need to pour castor oil into a glass or ceramic container and heat it to 50 degrees. Wipe pre-washed and dried boots with a sponge dipped in oil. Then you need to put on tight socks or socks on your feet and put shoes on them. It is recommended to walk in boots for about 3 hours. Then you can treat the shoes with castor oil a second time and walk a little more. The total duration of the procedure depends on how much you need to stretch the shaft.

Important Points

You can expand your shoes yourself if you know the features of stretching procedures.

Only shoes made of natural suede and leather can be stretched.
When buying shoes, you should ask if the store provides a service for stretching the tops. Sometimes it can be free.
Stretching shoes while wearing is almost impossible.
Be sure to expand the tops of the boots with locks. In narrow shoes, locks quickly break, which are susceptible to mechanical damage every time they are put on.
It is not necessary to use the services of a workshop to stretch shoes. There are many effective and safe ways how to increase the tops of boots at home.
One pair can be extended by 2-3 cm. It is undesirable to stretch the skin more, as it may tear.
When buying boots, you should pay attention to the presence of cuts with an inserted elastic band. They create additional comfort and make the shaft more elastic.

When freezing boots, it is important that water does not get on the skin, otherwise it may crack.
Freezer bags filled with gel can be used instead of water bags.
When stretching by freezing, do not immediately pull ice packs out of the boots. Frozen water expands and may damage the product.
If after the first time the boots did not stretch, the method used should be repeated.
When stretching shoes under the action high temperature wipe the skin with glycerin or cream. This will restore the desired level of humidity.

Almost everyone has a pair of rubber boots in their wardrobe. Like any thing, rubber shoes crack over time. In order not to throw away your favorite pair, you can try to repair it. How to seal rubber boots, described in the article.

Preparing boots for repair

A nail, a small shard of glass, or even a pebble with a sharp edge is enough to damage rubber shoes. One wrong move and the boot could crack.

Repair shops do not accept rubber shoes. This means that damaged boots can either be thrown away or repaired yourself.

How to seal rubber boots is a common question, the answer to which lies in the knowledge of some of the features of such a repair.

First you need to determine the location of the puncture or crack. To do this, you can take a container of water and a damaged boot. Roll up the freebie, starting at the top, like a tube of toothpaste. You should get a tight bundle. Next, lower the sole into the water. Air will escape from the puncture site, forming bubbles.

The next stage of preparation is the obligatory cleaning of boots from dirt and dust, degreasing and drying. Drying shoes is recommended to be carried out away from heat sources. Drying rubber boots on batteries can cause deformation, which will spoil their appearance and complicate the restoration process. All manipulations should be carried out carefully so as not to increase the size of the damage.

Then you should accurately determine the material from which the boots are made. Modern rubber shoes for women are made not only from rubber, but also from polyurethane, ethylene vinyl acetate (EVA). Each of these materials requires a different adhesive.

If it is difficult to determine the material of the boots on your own, you can take them with you to the store, where a specialist can quickly determine what the shoes are made of.

How to glue rubber boots

For gluing cracks in rubber boots, many people immediately buy a universal strong adhesive adhesive, known as "Moment". In fact, the composition of this product not only does not stick rubber, but can also ruin it. It will not be possible to achieve a good result with ordinary glue.

Repair of rubber boots should be carried out with special adhesives. High-quality products can be found in automotive and fishing stores. In this case, it is possible to purchase adhesives with a hermetic effect. They allow you to reliably glue cracks of any size and at the same time protect shoes from leakage.

The choice of a suitable adhesive depends on the technology of work. To date, there are several methods for the restoration of rubber shoes.

Anglers Method

Fishing and hunting stores sell special ones. They contain instructions that describe in detail the technology for using the product. For rubber boots, it is generally recommended to sand the damaged surface and apply a patch.

How to seal rubber boots if they are made of EVA? This material has a porous structure into which the adhesive is absorbed. No patches are needed to repair these boots. It is enough to apply the required amount of glue on the crack lines and press firmly. The hardening time of the product is indicated by the manufacturer on the packaging. After gluing, the boots will look like new, and the place with a defect will remain invisible.

The cyclist method

This method has been tested by many cyclists who often face the problem of a broken camera. For wheel repair, a bicycle repair kit is mainly used, consisting of patches on protective films, special glue for rubber and sandpaper.

According to this technology, it is necessary to rub the place where the patch will be applied with sandpaper, degrease with acetone and evenly apply glue. After a few minutes, you need to apply a patch and press firmly.

The bicycle repair method is reliable and guarantees high tightness. You can use glued boots almost immediately.

The disadvantage of this method is the unaesthetic appearance of the repaired product. A bicycle patch remains at the place of gluing, which is impossible not to notice. Therefore, in this way it is better to glue boots for summer cottages or fishing.

Automotive method

Many women ask how to seal rubber boots at the fold so that it is not noticeable. Boots made of rubber or EVA most often crack along the fold lines. A patch in such places is not always suitable and can spoil the appearance. Rubber shoes for women require a more careful repair, which can provide an elastic adhesive-sealant. It has a colorless viscous structure and is ideal for repairing colored and transparent rubber boots.

Today on sale there are automotive adhesives from different manufacturers. One of the best is Done Deal's Crazy Hands sealant. You can buy glue of this brand at any store for motorists.

Before applying the elastic bonding agent, it is necessary to treat the puncture or crack with acetone. After drying, apply glue.

Features of gluing the sole

Rubber shoes can be damaged in the sole area. How to seal a cut on a rubber boot? In this case, you can use any of the methods described above. Only preparation for gluing should take place a little differently. First of all, it is necessary to process the place of the cut on the grinding machine. The surface to be treated must be perfectly smooth. If this step is missed, the repair will not give a good result. Next, you should adhere to the technology of the chosen method.

To repair the sole, it is better to use adhesive sealants. Applying a patch in this place will not give a lasting result. When walking, the patch will quickly wear out, and soon there will be a need to replace it.

In order for the repaired shoes to serve as long as possible, it is important to know not only how to glue rubber boots, but also how to care for them.

Periodically wipe shoes with a cloth soft tissue dipped in a water-glycerin solution.
Dry rubber boots at room temperature away from batteries. Under the influence of hot air, the glued parts can become porous. As a result, the shoes may leak again.
Every time after a walk, clean your boots with a damp cloth. Dirt and dust can eat into the rubber, leaving stains. They are especially noticeable on light-colored shoes.
It is better to store rubber boots in cardboard box. For this purpose, it is recommended to keep the packaging in which they were sold.

It often happens that boots are ideal for the size of the foot, but they put a lot of pressure on the shins. From here, swelling of the limbs appears, walking becomes unbearable. To remedy the situation, people resort to all sorts of tricks. If we talk about boots made of thick leather, stretching the shaft is easy enough. But what about girls and women who wear boots made of thin material? Experienced housewives through trial and error, they came up with effective ways to help cope with the problem.

Method number 1. Shoe stretcher

In leather goods and footwear stores, you can purchase a special composition designed for such purposes. In some cases, the product is used to eliminate friction while wearing new shoes.

The technology for using products of this kind is quite transparent: spray the composition on the top area inside and out, put it on, fasten the zipper. Start doing household chores, wait until the shoes are completely dry. The method is good because the product perfectly stretches the boots, both from genuine leather, and a substitute.

The most popular means are considered to be the products of the company "Kiwi", "Twist", "Salamander", "Salton". The listed manufacturers produce products in the form of gels, sprays, foams. Choose the form of release at your discretion, they are all equally effective.

A feature of stretching patent or suede shoes is the fact that the composition must be applied exclusively from the inside. Otherwise, spots, cracks and stains will form on the surface of the product. The procedure can be repeated until you achieve the desired result.

Method number 2. Castor oil

Many people use castor oil to soften rough skin, but not everyone knows that a similar product can be used as a stretcher.

You can increase the shaft as follows: pour castor oil into a ceramic or glass bowl, heat it in the microwave to a temperature of 45-50 degrees. Wash and dry the shoes, moisten a foam sponge in oil and treat the boots from the outside and inside.

Put on knitted socks, leggings or thick high socks, fasten your boots, walk in them for about 3 hours. After the expiration of the period, without taking off your shoes, again walk over the surface with a sponge dipped in oil. The duration of exposure depends on how much you need to stretch the shaft.

After all the manipulations, take off your shoes, stuff your boots with cloth or newspapers, leave to dry completely. After the expiration of the period, wipe the outside with a flannel cloth, if necessary, stretch again.

Method number 3. frozen water

For effective stretching, you will need a thick plastic bag that will withstand freezing water and not tear. Pour cold water into the cavity, place the liquid bag inside the shaft, fasten the zipper. Send the product to the freezer until completely solidified.

It is known that when water freezes, it increases in size, along with this, the top will begin to stretch. Keep the boots in the freezer for about 5 hours after freezing, then remove and leave at room temperature for 3 hours. After that, fill the shaft with newspapers, wait for the final drying. Complete the manipulations with the treatment of shoes with cream, in case of insufficient results, stretch again.

Method number 4. Newspapers

As mentioned earlier, the shaft of a leather shoe stretches quite easily. natural materials elastic, but you should not make every effort so as not to damage the product. An excellent option for stretching is considered to be the use of paper or rags as stuffing.

To properly carry out the procedure, take an old rag or newspaper, crumple the material into a ball, then stuff the bootleg. Moisten shoes with water (temperature 40 degrees), leave to dry at room temperature. In no case do not dry your boots on heating radiators, otherwise they will lose their shape and become covered with bumps.

After 2-3 days, the shoes will be completely dry, you just have to pull out the padding and evaluate the result. If the shaft is not stretched enough, repeat the procedure, but this time put more newspapers. Finish stretching with nourishing cream to capture the result.

Method number 5. Iron

The stretching technology is designed for medium to thick skin. Can't be handled like this patent leather shoes, Lycra products or too thin skin. For the procedure, you will need a cotton or gauze cloth and an iron. If possible, involve an assistant in stretching, since the procedure is best performed together.

Set up an ironing board, unzip your boot and lay it zipper up. Heat the iron, soak a cloth in filtered (!) Water and place it in the inside of the boots on the shin area. Without sparing steam, start ironing the product, make sure that liquid does not drain from the iron. It is important to remember forever: only drinking water should be poured into the iron. It does not contain impurities and heavy metals, so it will not leave streaks.

When you have moistened the leather of the boots sufficiently, set the iron aside, then begin to stretch the tops in different directions. Try to perform the procedure without jerks, smoothly and evenly. In order not to overdo it with stretching, after steaming, measure the calf, then pull the skin to the required mark.

At the end of the treatment, fasten the boot, stuff it with a cloth or paper, leave to dry at room temperature. The newspaper must be rammed tightly, otherwise the skin will sit down. If desired, you can replace the paper with a wooden block of the right size. The duration of drying after such a procedure is approximately equal to 2-3 days.

Method number 6. Bottle and pencils

Pick up a glass bottle that will match the volume of the shaft in size. Soak the boot in hot water, insert a container into it, fasten the zipper. Now pour hot water into the jar, prepare pencils for drawing. Insert one stationery tool into the gap between the bottle and the wall of the shoe. Take the second pencil, do the same. Repeat the steps until there is no room left to insert the pencils.

After that, leave the shoes to dry at room temperature away from radiators. It will take about 2 days for the product to take shape. If the result is insufficient, carry out the procedure again. If the shoes are made of leatherette, the procedure is not recommended. Because of hot water material may bulge.

It's easy to stretch the tops of your boots at home if you stick to practical advice. Stuff shoes with old rags or newspapers, consider stretching using castor oil. Purchase a product for such purposes in the store, insert a bag of water into the shaft and freeze. Stretch the skin with a hot water bottle, leave to dry completely.