How to wash decorative stones in the garden. How to remove negative information from a stone Clean natural stones

Cut off a piece of metal mesh if you need to clean a small area. The easiest way to clean decorative stones is to sift through a mesh with a mesh size of 13 millimeters. The cells of such a mesh are 13 by 13 mm, so that the stones will remain on the surface of the sieve, and dirt and debris will be sifted through the mesh. A piece of mesh measuring 60 by 60 centimeters is quite enough for work.

• If your stones are smaller than this size, then you can use a grid with a cell size of 6.5 millimeters.

Make a wood mesh frame for large volumes. Use 5cm x 10cm boards (which you can find on hand) to make a rectangular frame of at least 0.35 square meters. The mesh should be cut to fit the frame and attached to the wood with strong staples.

• The sieve can be made in any size. This article suggests a minimum suitable size (0.35 square meters), but the area can be much larger. In some cases, it will be necessary to install wooden stiffeners across the mesh under the frame to prevent stones from crushing the mesh.

Lay out a tarp to keep the yard clear. If you want to quickly collect the dirt after cleaning the stones, then spread a large piece of tarp on the ground under the sieve. After work, you can simply lift the tarp and pour the garbage into a bucket.

• You can also immediately install the sieve on a large trash can.

Shovel the stones into the sieve. When everything is ready to work, start on one side of the rock area. Collect stones with a shovel and pour into a sieve. Be careful not to overload the sieve.

• Do not shovel earth with stones, otherwise you will only add work to yourself.

Shake the sieve with your hands or move the stones with a rake. If you have a small sieve, you can shake it from side to side to clear the stones of dirt. In the case of a large sieve for cleaning a large area, move the stones along the screen with a rake. Dirt and debris will immediately begin to sift through the mesh.

• If weeds, brushwood, clippings or other debris do not wake up through the net, they should be removed by hand.

Stack clean stones in a separate pile or return to their place. There are 2 main approaches: you can immediately return clean stones to their place or put them in a separate pile to distribute later on the site.

• The first option may be a little faster, but you run the risk of sifting some stones more than once.
• You can also work in small sections, return the stones to their place, and then move on to the next section. Experiment to find the best option.

Clear the entire area with decorative stones. Divide the site into sections or move around the perimeter and then towards the center. The cleared sections will be noticeable even if the stones are put in place right away, as they will look neater and not as tightly packed as the rest of the site.

• If the area is too large to handle in one day, try sifting one section of the area per day until the job is complete.

Not a single representative of the fair sex can do without means that emphasize her charm and attractiveness. Among them, not the last place is occupied by jewelry - jewelry and bijouterie, which provide many opportunities for the manifestation of the bright individuality of their owners. Modern jewelry from natural stones thanks to excellent processing and an abundance of designs, they allow you to realize any, even the most daring ideas for creating new looks.

The online store of natural stones and jewelry "World of Beauty" presents an extensive collection for true connoisseurs. Here you can buy jewelry made of natural stones both separately and in a set:

• Earrings with natural stones
• Rings with natural stones
• Bracelets with natural stones
• Brooches with natural stones
• Pendants with natural stones
• Rosary with natural stones

Online jewelry store - buy with profit

From the depths of centuries

Just think about the origin of the word "gem" and its deep meaning. Natural stones are called gems because their shade is a gift from nature itself. It cannot be artificially synthesized. Even the most accurate copies will still not be able to convey the full depth and saturation of the color that natural natural stones possess, which you can buy in our store. But beauty and indescribable brilliance and radiance are far from their only characteristics. Since ancient times, stone jewelry has been considered not as simple decorative trinkets, but as talismans that can cope with all sorts of problems. Modest at first glance, turquoise is a real source of happiness, bringing prosperity and peace to every home. Passionate pomegranate is able to give its owner true love, help the lonely find a life partner, even strengthen family bonds. Amethyst strengthens relationships, promotes friendship, business contacts and success, protects from a bad eye and unnecessary experiences. In a word, each stone has its own role, history and purpose. Now if you want buy jewelry from semi-precious stones , they can be chosen not only by appearance and your style preference. Determine for yourself what task you would like to solve today, and the right stone will help you!

Gem shop - buy without leaving home

Shopping with the help of the global network is now very few people will surprise. Its popularity is only growing over the years, because it is much more convenient to make purchases remotely, avoiding queues, crowds, fuss and noise of familiar retail outlets. Therefore, if you want to buy jewelry, an online store is a great option. Take a look at our comprehensive range. We have everything: bijouterie, jewelry, which you can buy at the best prices, watches, ritual and folklore accessories - rosaries, shambhala, many cute little things - bookmarks for books, makeup mirrors, hairpins, bag holders, Gift Baskets. All these goods - jewelry, bijouterie online store offers you to buy on especially favorable terms.

Our prices- in the category of the most affordable, but for wholesale customers and organizers of joint purchases, the cost of products is even lower. Bijouterie, online store, retail or wholesale are always available with us!

Why is our online jewelry store so popular?

A variety of stones, including passionate garnets, modest turquoise, delicate coral, mysterious amethyst, spectacular chrysoprase, exquisite pearls and an impressive list of others, no less beautiful and unusual materials, will make the study of our photo catalog a pleasant experience for you.

Our store presents such a wide assortment that each visitor can find a product in her favorite design and performance (for example, fashionable large beads or round earrings, rings with amber ...), buy a beautiful and at the same time inexpensive piece of jewelry for herself or loved ones. And, of course, most buyers return to the "World of Beauty" again for new clothes!

Author's jewelry made of natural stones - for connoisseurs of exclusivity

If you are faced with the choice of buying handmade or factory-made jewelry, then most likely stop at the first option. And this is not surprising, because designer jewelry always looks spectacular and unique. In addition, the probability of seeing a similar kit on someone is almost zero.

Excellent quality finishes, variety of designs, originality of products, reasonable prices - thanks to these factors, the sale of jewelry and bijouterie self made consistently popular.

"The World of Beauty" offers to choose and purchase jewelry with delivery in Moscow and other regions. Study catalogs, choose, compare - we are waiting for your orders!

Despite the strength, the stone is a very delicate material and requires care. This article provides recommendations for cleaning natural stone surfaces - how and with what to wash it. Even the types of stains are classified, because the choice of household chemicals depends on it.

General care

Any glasses, especially with spirits or citrus juice, put those on trays. Many drinks and foods contain acid that can corrode or discolor stone surfaces. Put hot dishes not on a stone surface, but on special rugs. Place mats or wipes under porcelain, ceramic, or silver items that may scratch the surface.

FLOOR SURFACES
Sweep floors with a dry, untreated mop or broom. Sand, dirt and abrasive particles cause the most damage to stone surfaces due to their abrasive ability. Mats and pads on either side of the main entrance will minimize the amount of sand, dirt and abrasive particles on the floor that can scratch the stone floor, as long as the bottom of the mat is non-slip. Usually eight steps is enough to get all the sand or mud off the soles of the boots. Do not use used vacuum cleaners, as their plastic or metal wheels and attachments may also scratch the surface.

OTHER SURFACES
Wash stone surfaces using a few drops of cleaner, "stone" soap (available from hardware stores or stone slab companies) or a mild liquid dish detergent and warm water. For best results, use a clean rag mop for mopping the floor and a soft cloth for mopping other surfaces. Too much detergent or soap may leave streaks. Do not use products containing citric, acetic or other acids on marble or limestone slabs. Thoroughly wash the surface after cleaning with soapy water and dry soft cloth. Change the water frequently, do not use washing powders or creams, as they contain abrasive substances that can scratch the surface.

BATHROOM AND OTHER WET SURFACES
In the bathroom or other damp areas, soap suds can be minimized by rubbing the surface with a rubber brush. To remove foam, use an acid-free foam remover or an aqueous solution of ammonia, although the stone surface may fade with too much ammonia.

WORK SURFACES
Work surfaces may require a primer. To avoid leaving traces of water, you need to treat the surface with non-yellowing wax in the form of a paste.

KITCHEN ZONE
Here, you may have to use a sealant or primer that does not contain toxic components. Always consult the manufacturer.

COVERED PATIO AND POOL AREA
In the pool, patio, or hot tub area, rinse with clean water and use a mild bleach solution to remove algae or moss.

Stone properties

Natural stone is of two types depending on the composition: siliceous or lime. Knowing the different properties of these stones is important when choosing cleaning products. Silicon stone is mainly composed of silicon and quartz particles, is wear resistant and can be easily cleaned with mild acid detergent solutions. Siliceous stones include granite, sandstone, quartzite, slate, ferruginous sandstone, and bluish sandstone (mica schist).

Lime stone is composed primarily of calcium carbonate. It cannot be washed with solutions containing acid, so it should be cleaned with other means than flint stone. Typical lime stones are marble, travertine, limestone and onyx. A simple acid sensitivity test will help determine the type of stone. You will need 120 g of a 10% hydrochloric acid solution or vinegar and a pipette. Since such an analysis can corrode the stone, conduct this experiment on some remaining fragment. Apply a few drops of the acid solution to the surface of the stone. If the stone is calcareous, the droplets of acid will begin to bubble or sizzle. If no noticeable reaction occurs, then you are dealing with a flint stone. Hydrochloric acid is a dangerous substance, so it is necessary to protect the surface of the skin from its accidental contact.

Get to know your stone

Granites and marbles mined in different parts of the world and come in different color shades and with different mineral compositions. In most cases, marbles and granites can be identified by visible particles on the surface of the stone. Marble usually shows "veining", or a high concentration of minerals. In granite, minerals are usually seen as small specks evenly distributed over the surface of the stone. Each stone has a unique color, texture and mottling.

Sandstones vary greatly in color, due to the fact that the stone may contain various minerals and clays. Shades can vary from light gray to yellow or reddish. Dark red-brown sandstone is also called iron sandstone. Bluish sandstone is a dense and hard stone with fine fibers that are greenish gray or bluish gray in color.

Limestone- a stone widely used in construction with light gray, dark yellow or light brown shades. A characteristic feature of many limestones is the presence of fossil remains in them, often visible on the surface of the stone. Slate is dark green, black, gray, dark red or multi-colored. It is most commonly used for floor slabs, roof tiles and has a distinct lobed texture.

stone finish

Polishing allows you to achieve a shiny surface that reflects light and emphasizes the color and texture of the material. A similar finish is used for walls, furniture and floor tiles.

polished texture It is a smooth, satiny surface that reflects light relatively poorly. In general, the polished finish is ideal for floors, stair treads, porch steps, and other high-traffic areas where polish can quickly fade. Polished texture is also used in furniture and for finishing other surfaces. The fire finish is a rough textured finish often seen on granite floor slabs.

Spots

SPILLS AND SPOTS
Wipe up spilled liquid immediately with paper towels. Do not rub this area, as this will only smear the spilled liquid. Wash the area several times with plain water and mild soap. Dry thoroughly with a soft cloth. Repeat if necessary. If the stain remains, refer to the stain removal section.

STAIN REMOVAL
Identifying the type of stain on a stone surface is the key to removing it. If you don't understand what's causing the pollution, try playing detective. Where is the stain located: next to a plant, a cooking area, or a bedroom where cosmetics are often used? What color is the spot? What shape or pattern is it? What happens in the area around the spot? Surface stains are often easily removed with a cleaning agent or household cleaners. Stains that are deeply ingrained in the texture of the stone or cannot be cleaned with conventional means may require special putties or the intervention of a professional.

Types of stains and the first steps to remove them

OIL-BASED (FAT, TAR, OIL, MILK, COSMETICS)
An oil stain causes the stone to darken and is usually dissolved by chemicals and then washed off. Gently wash the stained area with a mild, liquid bleach-based cleaner or household detergent, or ammonia, or lacquer thinner, or acetone.

ORGANIC (COFFEE, TEA, FRUIT, TOBACCO, PAPER, FOOD, URINE, LEAVES, BARK, BIRD DOORS)
Usually results in a pinkish-brown spot, but this may disappear once the source is removed. Ordinary rain and sun bleach and remove such spots on the street. In the room, you need to treat the stain with a 12% solution of hydrogen peroxide, and also drop a few drops of ammonia on it.

METAL (IRON, RUST, COPPER, BRONZE) Rust stains are orange to brownish in color. They can take the form of sources of contamination such as bolts, screws, tin cans, flower pots, metal fittings, etc. Copper-bronze stains are greenish or muddy-brown in color and are caused by exposure to moisture on nearby copper, bronze or brass items. Metal stains must be removed with a special putty or stain remover paste. It is extremely difficult to remove deeply ingrained rust.

BIOLOGICAL FORMATIONS (ALGAE, POWDER DEW, LICHEN, MOSS, FUNGI)
Rinse with a solution (half a cup per 3.5-4 liters of water) of ammonia, or bleach, or hydrogen peroxide. Do not mix bleach with ammonia! When combined, a toxic and deadly gas is formed.

INK
Rinse with bleach or hydrogen peroxide (light colored stones only!) or nail polish thinner or acetone (dark colored stones only!).

PAINT Small amounts can be removed with lacquer thinner or gently scraped off with a razor blade. A thick layer of paint can only be removed with a commercial thick paint remover solution available at a hardware store. These solutions usually contain caustic soda or alkali. Do not use acids to remove paint from stone. Paint strippers can corrode the surface of the stone and require repolishing. Follow the manufacturer's instructions and remember to thoroughly rinse the stained area with clean water. Protect your hands rubber gloves and eyes with special glasses and work in a well-ventilated area. Use only wooden or plastic scrapers to remove tar or paint clots. Usually emulsions and acrylic paints do not contaminate the surface. oil stains may appear when using oil paints, linseed drying oil, mastics, sealants and sealants.

DROPS AND RINGS OF WATER (SURFACE ACCUMULATION OF HARD WATER)
Polish with a dry iron brush.

FIRE AND SMOKE DAMAGE
Older stones and fireplaces with traces of smoke or fire may require more thorough cleaning to restore the original surface. Commercially available smoke removal products can save you time and effort.

TRACES OF CORROSION
They can be caused by acid remaining on the surface of the stone. Some materials may corrode the finish but not stain. Others corrode and stain the surface. After removing the stain, rinse the surface with clean water and apply a polishing powder, which can be purchased at the hardware store, to the marble. Rub the powder into the stone with a damp cloth. Polish until the mark disappears and the marble surface begins to shine again. Those marks that you cannot remove should be processed and removed by a professional polisher.

EFFLORESCENCE
Efflorescence refers to the white powder that can appear on the surface of the stone under the influence of water containing mineral salts and seeping out from under the surface of the stone. Water passes through the fibers of the stone and then evaporates. When evaporated, it leaves a powdery substance. If the slabs have been laid recently, wipe the area with a mop or remove the powder with a vacuum cleaner. You may need to repeat this procedure several times as the stone dries. Do not try to wash off the powder with water, because in this case it will disappear only for a while, and then come out again.

SCRATCHES AND CRACKS
Minor surface scratches can be removed with a dry iron brush. Deeper scratches and cracks in the surface of the stone should be repaired by a professional who will restore the polish.

Putties or pastes: how to use them

Putty is a liquid cleaning agent or chemical agent mixed with a white absorbent material. The result is a paste about the same consistency as peanut butter. A layer of paste 0.6-1.2 cm thick is applied to the contaminated surface with a wooden or plastic spatula. Then this place must be covered with plastic and left for 24-48 hours. The liquid cleaner or chemical will draw the stain into an absorbent absorbent. You may have to repeat this procedure several times to completely remove the stain.

Stain remover materials

They include kaolin, felting clay, whitewash, diatomaceous earth, crushed chalk, molding plaster or talc. Approximately four kilograms of stain remover paste is needed per square meter. Do not mix whitewash or felting (iron) clay with acidic chemicals, otherwise they will react and the stain removal effect will be nullified.

Cleaning products or household chemicals

OIL STAINS
Requires an aqueous solution of soda (sodium bicarbonate) or one of the powdered putty and lacquer thinner.

ORGANIC POLLUTANTS
Cover the stain with one of the powder pastes and treat with 12% hydrogen peroxide or replace the hydrogen peroxide with acetone.

RUST
Cover the stain with diatomaceous earth and a commercially available rust remover. Rust stains are difficult to remove and you may need to call in a professional service.

TRACES OF COPPER
Cover these places with one of the powdery, pasty materials and drip ammonia.

BIOLOGICAL FORMATIONS
Apply a solution of ammonia, or bleach, or hydrogen peroxide. Do not mix bleach with ammonia.

Prepare the putty.

If you are using powder, mix the detergent or household chemicals to the consistency of a thick paste. If you are using paper, soak it in a chemical solution and let dry, do not apply in liquid form. Wash the affected area with distilled water. Apply a layer of putty 0.6 to 1.2 cm thick: you must close the stain and smear the surface around it at a distance of 2.5 cm from the stain. Spread the paste evenly with a wooden or plastic scraper. Cover the putty with plastic and seal the edges with duct tape. Leave the putty to dry for 24-48 hours. During the drying process, the stain will be pulled out of the stone into the putty material. After about a day, remove the plastic, and let the putty dry further. Then you need to carefully remove the putty from the stain, rinse this place with clean water and wipe it with a dry soft cloth. If necessary, use a wooden or plastic scraper. Repeat this process up to five times until the stain is gone. If the surface is corroded by the chemical, apply polishing powder and buff with a jute cloth.

In this article:

Cleaning stones from plaque and dirt, as well as negative energy, is an important step in caring for jewelry. The fact is that stones, like any creatures on earth, love to be looked after. You need to clean your favorite products 1-2 times a month - this will be quite enough to bring the mineral back to normal and restore not only its shine, but also its strength.

stone cleaning

We clean the stones from dirt

It is no secret that plaque and dirt accumulate on the surface of products. Dust, contact with the human body and other negative factors affect the condition of jewelry. As a result of active wear, the minerals darken, and to eliminate this defect, you just need to clean the jewelry. You can do this in several ways:

1. Polishing.
2. Match cleaning.
3. Washing with water.
4. Salt baths.

Polishing is the easiest and effective method remove impurities from the surface of the crystal. Naturally, polishing will not remove stains and turbidity, but it will help to remove dust and dirt from the surface of the mineral that has accumulated on it for the whole day. Polishing the jewelry is easy, suede or cloth is suitable for this. The stone is carefully rubbed with a cloth, as a result of which it begins to shine.

Matches help to remove contaminants from the surface of minerals. Such a procedure requires attention and diligence. To do this, they simply set fire to matches, then extinguish them and rub the stones. It is said that this method helps to remove even old contaminants from the surface of the crystals.

Sometimes, in order to remove plaque and dirt from the surface of the stones, you just need to wash them. The procedure is carried out using a soapy solution and a toothbrush with soft bristles. The mineral is kept under a stream of water for several minutes and carefully rubbed with a brush, then polished with suede, velvet or flannel. But it should be borne in mind that some pebbles cannot be washed, they are afraid of water and can simply dissolve during the cleaning process.

Salt will help remove dirt from the surface of the jewelry. To do this, simply immerse jewelry with stones in a salt solution. The solution should be cool or warm, but not hot, as minerals are afraid high temperatures. The whole procedure lasts several minutes, do not immerse the crystals in the solution for more than half an hour. After finishing the treatment, it is necessary to wipe the jewelry with a dry soft cloth.

Having decided to clean the stones, it is worth bearing in mind that there are a number of rules that must not be violated. The fact is that crystals are afraid of:

• high temperatures;
• aggressive reagents;
• soaking.

Various kinds of stones are afraid of high temperatures. For this reason, it is not recommended to heat jewelry, boil it or immerse it in hot water. This will lead to the fact that the mineral will darken, stains will appear on its surface, which will be difficult to get rid of.

Do not clean gems with reagents - acids and alkalis will harm gems. They will lose their luster and color, and some substances are able to decompose the stone into molecules. For this reason, if the crystal needs cleaning, you should not experiment, it is better to give preference to specialized pastes. You can give jewelry to a jeweler, he will remove dirt and plaque from their surface.

Products inlaid with stones should not be soaked; a long stay of jewelry in water will not do them any good. Minerals may fall out or even lose their color. That is why you should not keep products in water or solution for longer than 20-30 minutes.

Experts also advise storing jewelry with crystals that do not differ in hardness separately, since other jewelry can harm the stones and scratch their surface. It is possible to correct such a defect, but for this the jeweler will have to grind the gem, remove chips from its surface.

We clean the gems from negative energy

Energetic charging of stones is also considered cleaning, but not dirt and plaque are removed from the minerals, but negative energy. Gems, like a sponge, accumulate bad emotions in themselves, for this reason it is worth processing crystals after each scandal or major quarrel. So that the stone does not stop working and brings good luck to the owner, it is necessary to regularly process it. In this case, the procedure should be carried out for all gems, even those that have just been bought in a store.

We clean pearls

So, how to rid the crystal of negative energy:

1. You can charge it with sunlight.
2. Cleanse with salt.
3. Treat with fire.
4. Energize herbs.
5. Purify the mineral with moonlight.

The rays of the sun help to rid the crystal of negative energy, for this it is worth leaving the gem under the rays of the sun for several hours. To carry out the procedure, you should choose a suitable place - put a stone on the windowsill so that the rays of the sun shine directly on it. The procedure lasts from several hours to several days, it will help charge the crystal with positive energy and cleanse it of negativity. But it is worth bearing in mind that the light of the sun can spoil the stone, change its color once and for all.

Cleaning with salt is carried out in several stages, it can be of two types. To charge the mineral with positive energy, it is enough to immerse it in sea salt. Salt crystals will absorb negative emotions and save the jewelry not only from negative energy, but also from dirt and plaque. The stone is cleaned for 2-3 hours, all this time it should be in a glass or ceramic dish with salt.

There is another way that will help restore the energy of the stone, for this they select dishes made of glass or ceramics, pour warm, clean water into it. Then sea salt is added to the water. When the water has cooled and the salt has completely dissolved, jewelry is immersed in the solution, the procedure lasts about 30 minutes. After the product is removed from the solution and wiped with a dry, clean cloth.

The next type of purification of minerals from negative energy is complex, but effective - stones are treated with fire. To do this, light a candle and learn a prayer. The gem is held over the fire and moved clockwise or counterclockwise, while it is necessary to read a prayer. The fire will take away the negativity and make the crystal completely pure. It should be put on the table, and then put in a dark place where the decoration will be for several days.

It is not difficult to charge gems with the energy of herbs, for this you need to grind medicinal herbs and place them in a glass dish. After that, jewelry must be placed in a mixture of herbs. They should be in the herbs for several hours.

They also fumigate with herbs - they are set on fire in a bowl, and then they process stones with a stream of smoke. It is not necessary to kindle a whole fire, which will let out puffs of smoke, a few streaming ribbons of smoke are enough to charge the stone. If the smell is embarrassing, then you need to add lavender to the bowl, it has a pleasant aroma.

The light of the moon is directly related to the energy of stones. It is used by magicians and sorcerers in order to make a powerful amulet out of this or that gem. It is worth charging the crystals at a certain time, the beginning of March is ideal for this.

When the moon enters the Aries phase, the mineral is placed in a special dish and a place is chosen. The light of the moon should fall directly on the stone, only in this case it will absorb the energy of this planet. If possible, it is better to leave the gems in the fresh air.

The moon will take away all the negativity from the mineral and endow it with powerful energy. But it is worth choosing the phase of the waning moon, only then will it take with it all the emotions that have accumulated in the stone.

When do gems need to be cleaned:

• if jewelry is considered a family heirloom and is inherited;
• if the jewelry was purchased at a pawnshop;
• if the products have absorbed negative energy after a quarrel or scandal;
• if the jewelry is constantly in contact with the wearer's body.

Those jewels that are inherited accumulate not only the emotions and feelings of the owners, but also their energy. For this reason, such products need to be cleaned. Before putting on such jewelry, it is worth charging them with “clean” energy.

In the pawnshop you can find beautiful products, but they all contain the energy of previous owners. To prevent damage to jewelry, they should be immersed in salt.

Quarrels, scandals, bad thoughts and deeds can spoil the stone, affect its energy. If the gem suddenly began to bring bad luck, it may be worth cleaning it.

Constant contact with the human body leads to the fact that the crystals are contaminated in the literal and figurative sense of the word. To prevent this from happening, it is worth charging gems 2-3 times a week.

Jewelry that has just been purchased in a store also needs to be energized. To do this, rinse jewelry in water. Running or tap water will do. But if possible, esotericists advise immersing the jewelry in a pond. A river or lake will do, just rinse the product in the river so that it gets rid of the negative.

Many people believe that stones have magical properties. So that these properties do not change, and the gems do not fade, they should be cleaned from time to time.

Regardless of what the gem is used for (medical, magical, or decoration), it needs to be looked after and sometimes cleaned. When you bought a stone, it must be cleaned. Hold it for a few minutes under running water. It is better, of course, if possible - to use natural spring water.

Minerals that belong to the quartz group can be put in a glass bowl of water and kept overnight in the freezer. You can stones and products from them in a vessel with water. Water, when frozen, will remove dirty information from the stone, and it will be cleansed. In this way, you can clean both stones that you used to wear, and new ones - bought or donated.

In the same way, not only newly acquired stones are cleansed, but also those that you already have. This must be done at least once a year, and health stones are cleansed once a month on the waning moon.

The general rule for cleaning stones is this: it is always better to clean all stones on the last three days of the lunar month (28, 29, 30) - before the new moon. On the full moon, stones accumulate energy and after cleaning they must have time to restore their own energy.

Tourmaline.

To store stones, it is best to use bags for each stone separately. The bag should be silk or cotton, linen can be. In such a package, gems can be stored in one box or box.

There are such methods of cleaning and updating natural stones(need to be clarified - not all methods are suitable for certain minerals). Precious stones are different in their properties and require individual approach to cleaning. If for some it is appropriate to use a soapy solution, then for others it can be disastrous. Improper cleaning can ruin your favorite jewelry.

1. Cleaning with water - the stone is kept under running water (from the tap) for several hours. It is better to put it in a bag and - in a spring, tie the bag so that it does not blow away. Or just pour spring water into a glass and put a stone in it.
2. Cleaning by the sun - pre-wash the stone with water and put it in the bright sun for 30 minutes. This is both purification and charging of the stone.
3. Cleaning with salt - bury the stone in salt for 3-4 hours, then discard the salt.
4. Cleaning with saline water - dip the stones in salted water poured into a crystal dish. You can use other dishes too, of course.
5. Cleaning with soapy water - prepare a soapy warm solution, pour it into a porcelain or crystal dish, and soak the stones in the sun for about two hours,
6. Earth cleansing - bury stones (this applies to cleaning gems) in the ground for the night.
7. Cleaning with natural sea water - wash the crystals with sea water, leave in it for 3 hours.

All stones from time to time it is useful to lay out for several hours or days in sunlight. This is especially true for those stones that you constantly wear. But - be careful - some stones change or lose color in the sun.

You can at least every day just wash the thing with water - the stone will only get better.

If the stone's hardness is above 5 ( sapphire, emerald, diamond, topaz, ruby, aquamarine, quartz, common beryl), then cleaning in a solution of any washing powder, using a brush. The exception would be jewelry that uses a soft metal, such as silver.. Gems framed in gold or platinum will take this cleaning well. After cleaning, rinse off the remaining solution with distilled water.

For cleaning stones, a solution consisting of 120 g of baking soda, 30 g of table salt and 50 g of bleach dissolved in 0.5 liters of water is suitable.

Gemstones are often very fragile and can easily crack if handled carelessly. This is especially true for those stones that have inclusions. Therefore, if you want to clean the chrysolite or emerald yourself, be very careful! Wrong movement - and a piece can break off from the stone.

Gemstones with a hardness value below 5 should be washed in a milder medium, such as soapy water. These stones include - apatite, ruby, opal, sunflower, Moonstone, chrysolite, lapis lazuli, malachite.

Ruby, alexandrite and sapphire can be cleaned in a soapy solution with ammonia. The proportions of the solution are 0.5 cups of water, 1 teaspoon of alcohol. After cleaning, rinse the gems with warm water.

Amethyst, rock crystal and citrine should only be cleaned with ultrasonic cleaners.

Turquoise- capricious gem. It cannot be cleaned with aqueous solutions; from their influence, the stone can easily lose color. Jewelry with turquoise should not be subjected to sudden changes in temperature, acidic and soapy solutions. To remove stubborn dirt, the use of alcohol or distilled water is allowed. To restore the shine, a piece of flannel fabric or dry suede is suitable - you can polish the turquoise yourself with them.

Very often dirt collects under the stone. You can remove it with a match and a piece of cotton wool. Moisten cotton wool with glycerin or a solution of magnesia and ammonia. Neat in a circular motion wipe the recesses and surfaces. If there are dirt particles that cannot be removed, contact a jewelry cleaning specialist. You may need professional cleaning with ultrasound. True, not all stones can be cleaned with ultrasound.

Universal way to clean any stones

Amethyst Druse.

Minerals put on the night for amethyst druse with very small crystals (it is also called an amethyst brush or bed for stones).

Also known purification of druzy quartz- place the stones on a quartz druse overnight.